/*項目：交通燈控制系統
*項目設計交通燈用于控制行人和車輛依 次通過十字路口。
*其設計要求 如 下: 1)、首先車行道亮綠燈 45s，同時人行道亮紅 45s；
*45s 后，2)、車行道黃燈閃爍 3 次，亮、滅各 1s，
*此時人行道 仍維持紅燈；
*3)、6s 后，轉為人行道亮綠燈 20s，車行道亮 紅燈 20s;
*4）、20s 后，再轉到 第 1步，如此循環往復； 5)
*51 系列單片機控制整個系統工 作； 6)交通信號燈用 LED 代 替；
*/
/**
*項目名稱：信號交通燈控制系統；
*作者：徐冉；
*日期：2013-06-01-10:00-13:45；
*說明:開源項目，基于AT89C52-RC單片機，51hei開發板；
*備注：系統已經順利通過調試，完美通過測試并成功實現系統功能，耗時3小時45分鐘；
**/
/*******************AT89C52-RC單片機****************************/
/*************************HL-1開發板***************************/
#include
typedef unsigned int uint;
typedef unsigned char uchar;
sbit wela = P2^7;
sbit dula = P2^6;
//車行道：信號交通燈
sbit cled_hong = P1^0; // 紅燈
sbit cled_lv = P1^2; //綠燈
sbit cled_huang = P1^4; //黃燈
//人行道：信號交通燈
sbit rled_hong = P1^1; //紅燈
sbit rled_lv = P1^3; //綠燈
//table:code
uchar code table[] = {
0x3F, //"0"
0x06, //"1"
0x5B, //"2"
0x4F, //"3"
0x66, //"4"
0x6D, //"5"
0x7D, //"6"
0x07, //"7"
0x7F, //"8"
0x6F //"9"
};
uchar sec, counter, counter1, flag, flag1;
//timer1&timer0:init
void init()
{
P1 = 0xff;
TMOD = 0x11;//T0，T1 工作方式1
TH0 = 0xB8; //定時20ms
TL0 = 0x00;
TH1 = 0xB8;
TL1 = 0x00;
TR0 = 1;
EA = 1;
ET0 = 1;
ET1 = 1;
}
//delay:xms
void delay(uint xms)
{
uchar i, j;
for(i = 0; i < xms; i++)
for(j = 0; j < 110; j++);
}
//display:
void display(uchar sec)
{
uchar cshi, cge;
cshi = sec / 10 % 10;
cge = sec % 10;
dula = 1;
P0 = table[cshi];
dula = 0;
P0 = 0xff;
wela = 1;
P0 = 0xfe;
wela = 0;
P0 = 0x00;
delay(1);
dula = 1;
P0 = table[cge];
dula = 0;
P0 = 0xff;
wela = 1;
P0 = 0xfd;
wela = 0;
P0 = 0x00;
delay(1);
}
//main:
void main(void)
{
init();
while(1)
{
display(sec);
rled_lv = 1;
cled_hong = 1;
rled_hong = 0;
cled_lv = 0;
if(flag == 1)
{
TR1 = 1;
rled_hong = 0;
cled_lv = 1;
}
if(flag1 == 1)
{
TR1 = 0;
cled_huang = 1;
rled_hong = 1;
cled_lv = 1;
rled_lv = 0;
cled_hong = 0;
}
}
}
//timer0:int
void timer0_int() interrupt 1
{
TH0 = 0xB8;
TL0 = 0x00;
counter++;
if(counter == 50)
{
counter = 0;
sec++;
if(sec >= 45)
{
flag = 1;
}
if(sec >= 51)
{
flag1 = 1;
flag = 0;
}
if(sec == 71)
{
sec = 0;
flag1 = 0;
P1 = 0xff;
rled_hong = 0;
cled_lv = 0;
rled_lv = 1;
cled_hong = 1;
cled_huang = 1;
}
}
}
//timer1:int
void timer1_int() interrupt 3
{
TH1 = 0XB8;
TL1 = 0X00;
counter1++;
if(counter1 == 50)
{
counter1 = 0;
cled_huang = ~cled_huang;
}
}