在线看毛片网站电影-亚洲国产欧美日韩精品一区二区三区,国产欧美乱夫不卡无乱码,国产精品欧美久久久天天影视,精品一区二区三区视频在线观看,亚洲国产精品人成乱码天天看,日韩久久久一区,91精品国产91免费

    
    
    <address id="vxupu"><td id="vxupu"></td></address>

      <pre id="vxupu"><small id="vxupu"></small></pre>
      <dfn id="vxupu"></dfn>
      <div id="vxupu"><small id="vxupu"></small></div>
    1. 新聞中心

      EEPW首頁 > 嵌入式系統 > 設計應用 > Stm32矩陣鍵盤掃描程序分析

      Stm32矩陣鍵盤掃描程序分析

      作者: 時間:2016-11-27 來源:網絡 收藏
      我們知道在51單片機中,通過掃描某個口的電平高低得知那個按鍵按下,比如,控制兩行4列,

      本文引用地址:http://www.biyoush.com/article/201611/322269.htm

      假如讓P1=0xCf;低位都置1(pb0-pb3),pb4-pb5置0;然后我們就掃描P1口就行了,如果有按鍵被按下的,高電平會被強制拉低的。

      假如按鍵返回的值為0xce,可知是pb0被拉低了,由此可判斷是S1或者S2按下了,其他的同理。

      當然只讓P1=0xcf,是不能判斷出具體的按鍵是哪個的,此時,如果我們?nèi)》醇萈1=0x30;

      當按鍵返回值為0x10時,我們可得知01 0000,pb5=0,s1或者s2被按下,這個時候我們將0xce|0x10=0xde,就是唯一的值了。以此類推,得出其他的值來。

      在stm32中是同樣的大道理;

      uint8_t KeyScan(void)

      {

      uint8_t HangValue = 0;

      uint8_t LieValue= 0;

      uint16_t KeyValue= 0;

      uint8_t Tmp =0;

      static uint8_t KeyConter = 0;

      GPIO_SetBits(Colum1.port, (Colum1.pin|Colum2.pin|Colum3.pin|Colum4.pin));

      GPIO_ResetBits(Line1.port,(Line1.pin|Line2.pin));

      Tmp = GPIO_ReadInputData(Line1.port);

      if ((Tmp&0x0F) != 0x0F)

      {

      if (KeyConter < 1)

      {//去抖

      KeyConter++;

      }

      else

      {

      HangValue = Tmp&0x0f;

      GPIO_ResetBits(Colum1.port, (Colum1.pin|Colum2.pin|Colum3.pin|Colum4.pin));

      GPIO_SetBits(Line1.port,(Line1.pin|Line2.pin));

      Tmp = GPIO_ReadInputData(Colum1.port);

      LieValue = Tmp&0x30;

      KeyValue = (HangValue)|LieValue;

      if (KeyValue)// KeyValue^KeyValueBkp

      {

      KeyValueBkp = KeyValue;

      switch (KeyValue)

      {

      //case KEY_10:return KEY_NUM_0;//16;----0

      case KEY_01:return KEY_NUM_1;//3;-----1

      case KEY_02:return KEY_NUM_2;//4;-----2

      case KEY_03:return KEY_NUM_3;//5;-----3

      case KEY_04:return KEY_NUM_4;//7;-----4

      case KEY_05:return KEY_NUM_5;//8;-----5

      case KEY_06:return KEY_NUM_6;//9;-----6

      case KEY_07:return KEY_NUM_7;//11----7

      case KEY_08:return KEY_NUM_8;//------8

      default:

      return 0;

      }

      }

      else

      {

      return 0;

      }

      }

      }

      else

      {

      KeyConter = 0;//計數清零

      KeyValueBkp = 0;

      }

      return 0;

      }

      typedef struct

      {

      GPIO_TypeDef*port;

      uint16_tpin;

      }Matrix_t;

      //const Matrix_t Colum1 = {GPIOD, GPIO_PIN_2};

      //const Matrix_t Colum2 = {GPIOD, GPIO_PIN_3};

      //const Matrix_t Colum3 = {GPIOD, GPIO_PIN_4};

      const Matrix_t Colum1 = {GPIOB, GPIO_Pin_0};

      const Matrix_t Colum2 = {GPIOB, GPIO_Pin_1};

      const Matrix_t Colum3 = {GPIOB, GPIO_Pin_2};

      const Matrix_t Colum4 = {GPIOB, GPIO_Pin_3};

      const Matrix_t Line1= {GPIOB, GPIO_Pin_4};

      const Matrix_t Line2= {GPIOB, GPIO_Pin_5};

      #define KEY_01 0x1e

      #define KEY_02 0x2e

      #define KEY_03 0x1d

      #define KEY_04 0x2d

      #define KEY_05 0x1b

      #define KEY_06 0x2b

      #define KEY_07 0x17

      #define KEY_08 0x27



      關鍵詞: Stm32矩陣鍵盤掃描程

      評論


      技術專區

      關閉