演示效果使用超級終端或者SecureCRT 5.5（這貨真的不錯）

工程結構圖：

1、工程里面的beep.c led.c usart1.c 與《STM32 基于庫函數控制按鍵&nb… 》《STM32 串口例程之查詢收》里面完全一樣，這里就不在上代碼。

2、main.c

//程序功能:主要用于測試SPI W25X16驅動是否正常

#include"stm32f10x.h"
#include"user_usart1.h"
#include"user_led.h"
#include"user_beep.h"
#include"user_spi_w25x16.h"
#include

#define FLASH_ID1 0xef3015
#define FLASH_ID2 0xef4015
#define FLASH_WriteAddress 0x000000
#define FLASH_ReadAddress FLASH_WriteAddress
#define FLASH_SectorErase FLASH_WriteAddress

#define CountOf(a) (sizeof(a)/sizeof(*(a)))
#define DataSize(CountOf(TxDataTable)-1)

u8 TxDataTable[]="Hello,I am wgchnln,我 愛 ARM,I will persist in learning ARM,堅決不放棄";
u8 RxDataTable[DataSize];

//=============================================
#ifdef __GNUC__

#define PUTCHAR_PROTOTYPE int __io_putchar(int ch)
#else
#define PUTCHAR_PROTOTYPE int fputc(int ch, FILE *f)
#endif
//=============================================

TestStatus User_SPI_DataCompare(u8 *TxData,u8 *RxData,u8 Num)
{
while(Num--)
{
if(*TxData!=*RxData)
{
return Failed;
}
RxData++;
TxData++;
}

return Successed;
}

void User_SPI_Test(void)
{
vu32 ID,DeviceID;
u8 Buffer;
volatile TestStatus Test1=Failed;
volatile TestStatus Test2=Successed; //存放兩次測試的結果


printf("正在努力讀取ID號.....");
User_LedSpark(Led1,2);
ID=User_SPI_W25X16_ReadID();
printf("flashID:%x",ID);

printf("正在努力讀取DeviceID號......");
User_LedSpark(Led1,2);
DeviceID=User_SPI_W25X16_ReadDeviceID();
printf("flashDeviceID:%x",DeviceID);



if((ID==FLASH_ID1)||(ID==FLASH_ID2))
{

printf("ARM在芯片擦除......");
User_LedSpark(Led1,2);
User_SPI_W25X16_SectorErase(FLASH_SectorErase);
printf("完成");

printf("你要寫入的數據:%s",TxDataTable);
printf("努力為你芯片寫入中......");
User_LedSpark(Led1,2);
User_SPI_W25X16_ChipWrite(TxDataTable,FLASH_WriteAddress,DataSize);
printf("完成");

printf("芯片數據讀取......");
User_LedSpark(Led1,2);
User_SPI_W25X16_ChipRead(RxDataTable,FLASH_ReadAddress,DataSize);
printf("完成");
User_LedSpark(Led1,2);
printf("為您讀取的數據:%s",RxDataTable);

printf("為您做數據比較中......");
User_LedSpark(Led1,2);
Test1=User_SPI_DataCompare(RxDataTable,TxDataTable,DataSize);
if(Test1==Successed)
{
printf("數據相同");
}
else
{
printf("數據不相同");
User_LedSpark(Led2,2);
printf("為您分析可能原因:數據未寫入、讀取錯誤、或者兩者同時存在");
}

printf("再一次芯片擦除......");
User_LedSpark(Led1,2);
User_SPI_W25X16_SectorErase(FLASH_SectorErase);
printf("完成");

printf("又一次芯片讀取......");
User_LedSpark(Led1,2);
User_SPI_W25X16_ChipRead(RxDataTable,FLASH_ReadAddress,DataSize);
printf("完成");

printf("判斷是否擦除掉......");
User_LedSpark(Led1,1);
for(Buffer=0;Buffer
{
if(RxDataTable[Buffer]!=0xff)
{
Test2=Failed;
}
}
if(Test2==Failed)
{
printf("失敗");
printf("為您分析的可能原因:讀取錯誤、擦除失敗、或者兩者同時存在");
}
else
{
printf("擦除OK");
}

printf("------------為您展示此次測試結果------------");
if((Test1==Successed)&&((Test2==Successed)))
{
User_LedSpark(Led1,2);
printf("恭喜你,SPI W25X16驅動測試通過啦");
}
else
{
User_LedSpark(Led2,2);
printf("糟糕,SPI功能演示失敗了......原因可能是讀寫數據不一致、軟件擦除失敗");
}
}


else
{
User_LedSpark(Led2,2);
printf("悲劇了,SPI功能演示失敗啦.....原因是芯片ID號碼讀取出錯哦");
}
}

int main(void)
{
User_USART1Config();
printf("串口1配置......");
printf("完成");

printf("蜂鳴器初始化...");
User_BeepConfig();
printf("蜂鳴器測試......");
User_BeepStatus(BeepStatus_TurnOn);
printf("完成");

printf("LED初始化...");
User_LedConfig();
printf("LED測試......");
User_LedSpark(Led0,2);
printf("完成");

printf("SPI初始化...");
User_SPI_Config();
User_LedSpark(Led0,2);
printf("完成");

User_SPI_Test();

while(1);
}

//==================================================
PUTCHAR_PROTOTYPE
{


USART_SendData(USART1, (uint8_t) ch);

while (USART_GetFlagStatus(USART1, USART_FLAG_TC) == RESET)
{}

return ch;
}
//==================================================

3、user_spi_w25x16.c

//program function:SPI1 Init && FLASF Chip W25X16 driver

#include"stm32f10x.h"
#include"user_spi_w25x16.h"
#include

#define WriteEnable0x06
#define WriteDisable0x04
#define ReadStatusRegister0x05
#define WriteStatusRegister0x01
#define ReadData0x03
#define FastRead0x0b
#define FsatReadDualOutput0x3b
#define PageProgram0x02
#define BlukErase0xd8
#define SectorErase0x20
#define ChipErase0xc7
#define PowerDown0xb9
#define WakeUp0xab
#define DeviceID0xab
#define ManufatureID0x90
#define JedecID0x9f

#define JudgeCode0x01 //用于判斷通訊是否結束用
#define NoneCode0xa5 //無意義的指令，用于:接收數據時，發送這個質量來產生接收時候的時鐘

void User_SPI_Config(void)
{


SPI_InitTypeDef SPI_InitStructure;

GPIO_InitTypeDef GPIO_InitStructure;

RCC_APB2PeriphClockCmd(SPI_24G_CS_Clock,ENABLE);
GPIO_InitStructure.GPIO_Pin =SPI_24G_CS_Pin;
GPIO_InitStructure.GPIO_Mode =GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed =GPIO_Speed_50MHz;
GPIO_Init(SPI_24G_CS_Port,&GPIO_InitStructure);
GPIO_SetBits(SPI_24G_CS_Port,SPI_24G_CS_Pin);

RCC_APB2PeriphClockCmd(SPI_VS1003B_CS_Clock,ENABLE);
GPIO_InitStructure.GPIO_Pin =SPI_VS1003B_CS_Pin;
GPIO_InitStructure.GPIO_Mode =GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed =GPIO_Speed_50MHz;
GPIO_Init(SPI_VS1003B_CS_Port,&GPIO_InitStructure);
GPIO_SetBits(SPI_VS1003B_CS_Port,SPI_VS1003B_CS_Pin);

RCC_APB2PeriphClockCmd(SPI_W25X16_Clock,ENABLE);

RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO,ENABLE);

RCC_APB2PeriphClockCmd(SPI_W25X16_CS_Clock,ENABLE);
GPIO_InitStructure.GPIO_Pin =SPI_W25X16_CS_Pin;
GPIO_InitStructure.GPIO_Mode =GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed =GPIO_Speed_50MHz;
GPIO_Init(SPI_W25X16_CS_Port,&GPIO_InitStructure);
SPI_W25X16_CS_DisSelect;

RCC_APB2PeriphClockCmd(SPI_W25X16_SCK_Clock,ENABLE);
GPIO_InitStructure.GPIO_Pin =SPI_W25X16_SCK_Pin;
GPIO_InitStructure.GPIO_Mode =GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed =GPIO_Speed_50MHz;
GPIO_Init(SPI_W25X16_SCK_Port,&GPIO_InitStructure);

RCC_APB2PeriphClockCmd(SPI_W25X16_MISO_Clock,ENABLE);
GPIO_InitStructure.GPIO_Pin =SPI_W25X16_MISO_Pin;
GPIO_Init(SPI_W25X16_MISO_Port,&GPIO_InitStructure);

RCC_APB2PeriphClockCmd(SPI_W25X16_MOSI_Clock,ENABLE);
GPIO_InitStructure.GPIO_Pin =SPI_W25X16_MOSI_Pin;
GPIO_Init(SPI_W25X16_MOSI_Port,&GPIO_InitStructure);

SPI_InitStructure.SPI_Direction =SPI_Direction_2Lines_FullDuplex; //通訊模式:雙向全雙工模式
SPI_InitStructure.SPI_Mode =SPI_Mode_Master;//主從:主模式
SPI_InitStructure.SPI_DataSize =SPI_DataSize_8b;//數據幀長度:8bits
SPI_InitStructure.SPI_CPOL =SPI_CPOL_High;//空閑時置高
SPI_InitStructure.SPI_CPHA =SPI_CPHA_2Edge;//第二個時鐘采樣
SPI_InitStructure.SPI_NSS =SPI_NSS_Soft;//NSS控制選擇:軟件控制
SPI_InitStructure.SPI_BaudRatePrescaler =SPI_BaudRatePrescaler_2;//波特率分配系數:2分頻
SPI_InitStructure.SPI_FirstBit =SPI_FirstBit_MSB;//數據幀格式:MSB在前
SPI_InitStructure.SPI_CRCPolynomial =7;//CRC效驗多項式

SPI_Init(SPI1,&SPI_InitStructure);

SPI_Cmd(SPI1,ENABLE);
}

u8 User_SPI_W25X16_SendByte(u8 SendByteData)
{
u8 ReceiveData;


while(SPI_I2S_GetFlagStatus(SPI1,SPI_I2S_FLAG_TXE)!=SET);

SPI_I2S_SendData(SPI1,SendByteData);

while(SPI_I2S_GetFlagStatus(SPI1,SPI_I2S_FLAG_RXNE)!=SET);

ReceiveData=SPI_I2S_ReceiveData(SPI1);

return ReceiveData;
}

u8 User_SPI_W25X16_ReadByte(void)
{
u8 ReceiveData;

ReceiveData=User_SPI_W25X16_SendByte(NoneCode);

return ReceiveData;
}

vu16 User_SPI_W25X16_SendHalfWord(u16 HalfWord)
{
vu16 ReceiveData;

while(SPI_I2S_GetFlagStatus(SPI1,SPI_I2S_FLAG_TXE)!=SET);

SPI_I2S_SendData(SPI1,HalfWord);

while(SPI_I2S_GetFlagStatus(SPI1,SPI_I2S_FLAG_RXNE)!=SET);

ReceiveData=SPI_I2S_ReceiveData(SPI1);

return ReceiveData;
}

void User_SPI_W25X16_WriteEnable(void)
{

SPI_W25X16_CS_Select;

User_SPI_W25X16_SendByte(WriteEnable);

SPI_W25X16_CS_DisSelect;
}