//主機板的P1接口 平接 顯示板P00接口 即數(shù)碼管段選接口
//主機板的P3接口 平接 顯示板P20接口 即數(shù)碼管位選接口
//主機板的P0接口 平接 顯示板燈的接口

#include
unsigned char time[10]={0x3F,0x06,0x5B,0x4F,0x66,0x6D,0x7D,0x07,0x7F,0x6F};
int n = 2000;//每半秒中斷一次

bit change=1;
bit Shan=1;//閃

//定義顯示管為位選特殊位
sbit A=P3^7;
sbit B1=P3^6;
sbit C=P3^5;
sbit G1=P3^4;
sbit daul = P3^3;

ZY();//左右通行
SX();//上下通行
ZYS();//左右綠燈閃
SXS();//上下綠燈閃

lock();
delay();

//一下定義使燈亮的特殊位
sbit ZL=P0^0;
sbit ZH=P0^1;
sbit SH=P0^2;
sbit SL=P0^3;
sbit YH=P0^4;
sbit YL=P0^5;
sbit XH=P0^6;
sbit XL=P0^7;
//
unsigned char rl=70;
unsigned char ud=45;
unsigned int working=0;//
unsigned char num;

main()
{
TMOD=2;//設置定時/計數(shù)器0工作方式2
TH0=6;//初值為6,定時4000
TL0=6;//初值為6
TR0=1;
ET0=1;
EA=1;
working = rl*2;

while(1){
if(change==1&&Shan==1){//
ZY();
}else if(change==1&&Shan==0){
ZYS();
}else if(change==0&&Shan==1){
SX();
}else if(change==0&&Shan==0){
SXS();
}

num=working/2;

P1=time[num];
daul=1;
A=1;B1=1;C=1;
G1=1;
delay();
lock();

P1=time[num/10];
daul=1;
A=0;B1=1;C=1;
G1=1;
delay();
lock();

}

//
}

//中斷程序

T0_int() interrupt 1{
n--;
if(n==0){
if(working!=0&&change==1){
if(working<=4){//最后兩秒閃
Shan=!Shan;
}
working--;
n=2000;
}else if(working==0&&change==1){
change=!change;
working = ud*2;
n=2000;
}else if(working!=0&&change==0){
if(working<=6){//最后3秒閃
Shan=!Shan;
}
working--;
n=2000;
}else if(working==0&&change==0){
change=!change;
working = rl*2;
n=2000;
}
}
}

ZY(){//左右綠燈亮，上下紅燈亮
YL=0;//右綠
ZL=0;//左綠
SH=0;//上紅
XH=0;//下紅
//
ZH=1;
YH=1;
SL=1;
XL=1;
}

SX(){//上下綠燈亮，左右紅燈亮
YL=1;//
ZL=1;
SH=1;
XH=1;
//
ZH=0;
YH=0;
SL=0;
XL=0;
}

ZYS(){//左右綠燈閃爍
YL=1;
ZL=1;
SH=0;
XH=0;
//
ZH=1;
YH=1;
SL=1;
XL=1;
}

SXS(){//上下綠燈閃爍
YL=1;//
ZL=1;
SH=1;
XH=1;
//
ZH=0;
YH=0;
SL=1;
XL=1;
}

lock(){
daul=0;
G1=0;
}

delay(){
int i=40;
while(i>0){
i--;
}
}