Main文件

#include"stm32f10x.h"

voidRCC_Configuration(void);

voidGPIO_Configuration(void);

voidEXTI_Configuration(void);//外部中斷設置

voidNVIC_Configuration(void);//中斷優先級別設置

unsignedcharled_bit1=0;

unsignedcharled_bit2=0;

intmain(void)

{

RCC_Configuration();

GPIO_Configuration();

EXTI_Configuration();

NVIC_Configuration();

GPIO_SetBits(GPIOA,GPIO_Pin_0);

GPIO_SetBits(GPIOA,GPIO_Pin_1);

while(1);

}

voidRCC_Configuration(void)

{

RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA |RCC_APB2Periph_AFIO ,ENABLE);

}

voidGPIO_Configuration(void)

{

GPIO_InitTypeDefGPIO_InitStructure;

GPIO_InitStructure.GPIO_Pin=GPIO_Pin_0|GPIO_Pin_1;

GPIO_InitStructure.GPIO_Speed=GPIO_Speed_50MHz;

GPIO_InitStructure.GPIO_Mode=GPIO_Mode_Out_PP;

GPIO_Init(GPIOA,&GPIO_InitStructure);

GPIO_InitStructure.GPIO_Pin=GPIO_Pin_3|GPIO_Pin_8;

GPIO_InitStructure.GPIO_Mode=GPIO_Mode_IN_FLOATING;

GPIO_InitStructure.GPIO_Speed=GPIO_Speed_50MHz;

GPIO_Init(GPIOD,&GPIO_InitStructure);

}

voidEXTI_Configuration(void)

{

EXTI_InitTypeDefEXTI_InitStructure;

GPIO_EXTILineConfig(GPIO_PortSourceGPIOA,GPIO_PinSource3);

EXTI_InitStructure.EXTI_Line=EXTI_Line3;

EXTI_InitStructure.EXTI_Mode=EXTI_Mode_Interrupt;

EXTI_InitStructure.EXTI_Trigger=EXTI_Trigger_Falling;

EXTI_InitStructure.EXTI_LineCmd=ENABLE;

EXTI_Init(&EXTI_InitStructure);

GPIO_EXTILineConfig(GPIO_PortSourceGPIOA,GPIO_PinSource8);

EXTI_InitStructure.EXTI_Line=EXTI_Line8;

EXTI_InitStructure.EXTI_Mode=EXTI_Mode_Interrupt;

EXTI_InitStructure.EXTI_Trigger=EXTI_Trigger_Falling;

EXTI_InitStructure.EXTI_LineCmd=ENABLE;

EXTI_Init(&EXTI_InitStructure);

}

voidNVIC_Configuration(void)

{

/*

查看固件庫手冊，關于中斷部分NVIC_IRQChannel

PA3、PA8分別設置

EXTI3_IRQChannel外部中斷線3中斷

EXTI9_5_IRQChannel外部中斷線9-5中斷

關于中斷線，查看STM32 Reference Manual的9.2.5外部中斷/事件線路映像

stm32使用了4個位來保存優先級別

查固件庫

Table273.先占優先級和從優先級值

占先優先級->主

副優先級->次

號碼越小，等級越高

判斷主的級別->一個高一個低->ok

判斷主的級別->兩個都相同->判斷次的級別->一個高一個低->ok

判斷主的級別->兩個都相同->判斷次的級別->兩個都相同->按照列表順序運行

*/

NVIC_InitTypeDefNVIC_InitStructure;

NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);//占先優先級、副優先級的資源分配

NVIC_InitStructure.NVIC_IRQChannel=EXTI3_IRQn;//指定中斷源

NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=1;//占先優先級設定

NVIC_InitStructure.NVIC_IRQChannelSubPriority=0;//副優先級設定

NVIC_InitStructure.NVIC_IRQChannelCmd=ENABLE;

NVIC_Init(&NVIC_InitStructure);

NVIC_InitStructure.NVIC_IRQChannel=EXTI9_5_IRQn;

NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=0;

NVIC_InitStructure.NVIC_IRQChannelSubPriority=0;

NVIC_Init(&NVIC_InitStructure);

}

stm32f10x_it.c中加入

externunsignedcharled_bit1,led_bit2;

voidEXTI9_5_IRQHandler(void)

{

if(EXTI_GetITStatus(EXTI_Line8)!=RESET)

{

//添加中斷處理程序

if(led_bit1)

{

GPIO_SetBits(GPIOA,GPIO_Pin_1);

led_bit1=0;

}

else

{

GPIO_ResetBits(GPIOA,GPIO_Pin_1);

led_bit1=1;

}

EXTI_ClearFlag(EXTI_Line8);

}

}

voidEXTI3_IRQHandler(void)

{

if(EXTI_GetITStatus(EXTI_Line3)!=RESET)

{

if(led_bit2)

{

GPIO_SetBits(GPIOA,GPIO_Pin_0);

led_bit2=0;

}

else

{

GPIO_ResetBits(GPIOA,GPIO_Pin_0);

led_bit2=1;

}

EXTI_ClearFlag(EXTI_Line3);

}

}