Virtex-6 FPGA適合用有線通信,無線基礎設備和廣播設備等領域.本文介紹了Virtex-6 FPGA主要特性,以及骨干網OTU-4成幀與EFEC框圖, LTE 2x2無線電設計框圖和支持SD/HD/3G-SDI接口的新一代交換框圖, Virtex®-6 FPGA ML605評估套件主要特性和詳細電路圖.

The Virtex®-6 family provides the newest, most advanced features in the FPGA market. Virtex-6 FPGAs are the programmable silicon foundation for Targeted Design Platforms that deliver integrated software and hardware components to enable designers to focus on innovation as soon as their development cycle begins. Using the third-generation ASMBL (Advanced Silicon Modular Block) columnbased architecture, the Virtex-6 family contains multiple distinct sub-families. This overview covers the devices in the LXT, SXT, and HXT sub-families. Each sub-family contains a different ratio of features to most efficiently address the needs of a wide variety of advanced logic designs. In addition to the high-performance logic fabric, Virtex-6 FPGAs contain many built-in system-level blocks. These features allow logic designers to build the highest levels of performance and functionality into their FPGA-based systems. Built on a 40 nm state-of-theart copper process technology, Virtex-6 FPGAs are a programmable alternative to custom ASIC technology. Virtex-6 FPGAs offer the best solution for addressing the needs of high-performance logic designers, high-performance DSP designers, and high performance embedded systems designers with unprecedented logic, DSP, connectivity, and soft microprocessor capabilities.

Virtex-6 FPGA 主要特性:

Three sub-families:

Virtex-6 LXT FPGAs: High-performance logic with advanced serial connectivity

Virtex-6 SXT FPGAs: Highest signal processing capability with advanced serial connectivity

Virtex-6 HXT FPGAs: Highest bandwidth serial connectivity

Compatibility across sub-families

LXT and SXT devices are footprint compatible in the same package

Advanced, high-performance FPGA Logic

Real 6-input look-up table (LUT) technology

Dual LUT5 (5-input LUT) option

LUT/dual flip-flop pair for applications requiring rich register mix

Improved routing efficiency

64-bit (or two 32-bit) distributed LUT RAM option per 6-input LUT

SRL32/dual SRL16 with registered outputs option

Powerful mixed-mode clock managers (MMCM)

MMCM blocks provide zero-delay buffering, frequency synthesis, clock-phase shifting, inputjitter filtering, and phase-matched clock division

36-Kb block RAM/FIFOs

Dual-port RAM blocks

Programmable

- Dual-port widths up to 36 bits

- Simple dual-port widths up to 72 bits

Enhanced programmable FIFO logic

Built-in optional error-correction circuitry

Optionally use each block as two independent 18 Kb blocks

High-performance parallel SelectIO technology

1.2 to 2.5V I/O operation

Source-synchronous interfacing using ChipSync technology

Digitally controlled impedance (DCI) active termination

Flexible fine-grained I/O banking

High-speed memory interface support with integrated write-leveling capability

Advanced DSP48E1 slices

25 x 18, two’s complement multiplier/accumulator

Optional pipelining

New optional pre-adder to assist filtering applications

Optional bitwise logic functionality

Dedicated cascade connections

Flexible configuration options

SPI and Parallel Flash interface

Multi-bitstream support with dedicated fallback reconfiguration logic

Automatic bus width detection

System Monitor capability on all devices

On-chip/off-chip thermal and supply voltage monitoring

JTAG access to all monitored quantities

Integrated interface blocks for PCI Express® designs

Compliant to the PCI Express Base Specification 2.0

Gen1 (2.5 Gb/s) and Gen2 (5 Gb/s) support with GTX transceivers

Endpoint and Root Port capable

x1, x2, x4, or x8 lane support per block

GTX transceivers: up to 6.6 Gb/s

Data rates below 480 Mb/s supported by oversampling in FPGA logic.

GTH transceivers: 2.488 Gb/s to beyond 11 Gb/s

Integrated 10/100/1000 Mb/s Ethernet MAC block

Supports 1000BASE-X PCS/PMA and SGMII using GTX transceivers

Supports MII, GMII, and RGMII using SelectIO technology resources

2500Mb/s support available

40 nm copper CMOS process technology

1.0V core voltage (-1, -2, -3 speed grades only)

Lower-power 0.9V core voltage option (-1L speed grade only)

High signal-integrity flip-chip packaging available in standard or Pb-free package options

Virtex®-6 FPGA典型應用:


圖1.骨干網OTU-4成幀和EFEC框圖(有線通信)

圖2. LTE 2x2無線電設計框圖(無線基礎設備)

圖3.支持SD/HD/3G-SDI接口的新一代交換框圖(廣播通信)