25045操作標準子程序

# include stdio.h>
# include reg52.h>
# define uchar unsigned char
# define uint unsigned int
sbit SO=P1^1;/*25045輸出*/
sbit SI=P1^2;/*25045輸入*/
sbit SCK=P1^3;/*25045時鐘*/
sbit CS=P1^4;/*25045片選*/
uchar code WREN_INST=0X06;
/* Write enable latch instruction (WREN)*/
uchar code WRDI_INST=0X04;
/* Write disable latch instruction (WRDI)*/
uchar code WRSR_INST=0X01;
/* Write status register instruction (WRSR)*/
uchar code RDSR_INST=0X05;
/* Read status register instruction (RDSR)*/
uchar code WRITE_INST=0X02;
/* Write memory instruction (WRITE)*/
/*寫入25045的先導字,應當為0000A010,其中的A為寫入25045的高位地址
將此WRITE_INST和寫入高位地址相或后即為正確的寫先導字*/
uchar code READ_INST=0X03;
/* Read memory instruction (READ)*/
/*讀出25045的先導字,應當為0000A011,其中的A為讀出25045的高位地址
將此READ_INST和讀出高位地址相或后即為正確的讀先導字*/
uint code BYTE_ADDR=0X55;
/* Memory address for byte mode operations*/
uchar code BYTE_DATA=0X11;
/*Data byte for byte write operation*/
uint code PAGE_ADDR=0X1F;
/* Memory address for page mode operations*/
/*頁面寫入的其始地址*/
uchar code PAGE_DATA1=0X22;
/* 1st data byte for page write operation*/
uchar code PAGE_DATA2=0X33;
/* 2nd data byte for page write operation*/
uchar code PAGE_DATA3=0X44;
/* 3rd data byte for page write operation*/
uchar code STATUS_REG=0X20;
/* Status register,設置DOG時間設置為200毫秒,無寫保護*/
/*這是狀態寄存器的值,他的意義在于第5,第4位為WDI1,WDI0代表DOG的時間,00為1.4秒,01為600毫秒,10為200毫秒,00為disabled
第3位和第2位為BL1,BL0,是寫保護設置位,00為無保護,01為保護180-1FF,10為保護100-1FF,11為保護000-1FF.第1位為WEL,
當他為1時代表已經寫使能設置了,現在可以寫了,只讀位.第0位為WIP,當他為1時代表正在進行寫操作,是只讀*/
uchar code MAX_POLL=0x99;
/* Maximum number of polls*/
/*最大寫過程時間,確定25045的最大的寫入過程的時間*/
uchar code INIT_STATE=0x09;
/* Initialization value for control ports*/
uint code SLIC=0x30;
/* Address location of SLIC*/
void wren_cmd(void);/*寫使能子程序*/
void wrdi_cmd(void);/*寫使能復位*/
void wrsr_cmd(void);/*復位時間位和數據保護位寫入狀態寄存器*/
uchar rdsr_cmd(void);/*讀狀態寄存器*/
void byte_write(uchar aa,uint dd);/*字節寫入,aa為寫入的數據,dd為寫入的地址*/
uchar byte_read(uint dd);/*字節讀出,dd為讀出的地址,返回讀出的數據*/
void page_write(uchar aa1,uchar aa2,uchar aa3,uchar aa4,uint dd);/*頁寫入*/
void sequ_read(void);/*連續讀出*/
void rst_wdog(void);/*DOG復位*/
void outbyt(uchar aa);/*輸出一個字節到25045中，不包括先導字等*/
uchar inputbyt();/*由25045輸入一個字節，不包括先導字等額外的東西*/
void wip_poll(void);/*檢查寫入過程是否結束*/


/*25045操作子程序集*/
/*;*******************************************************
*
;* Name: WREN_CMD
;* Description: Set write enable latch
;* Function: This routine sends the command to enable writes to the EEPROM memory array or
;* status register
;* Calls: outbyt
;* Input: None
;* Outputs: None
;* Register Usage: A
;*****************************************************
*/
/*寫使能子程序*/
void wren_cmd(void)
{
uchar aa;
SCK=0;/* Bring SCK low */
CS=0;/* Bring /CS low */
aa=WREN_INST;
outbyt(aa);/* Send WREN instruction */
SCK=0;/* Bring SCK low */
CS=1;/* Bring /CS high */
}

/*;***********************************************************
*
;* Name: WRDI_CMD
;* Description: Reset write enable latch
;* Function: This routine sends the command to disable writes to the EEPROM memory array or
;* status register
;* Calls: outbyt
;* Input: None
;* Outputs: None
;* Register Usage: A
;***********************************************************
*/
/*寫使能復位子程序*/
void wrdi_cmd(void)
{
uchar aa;
SCK=0;/* Bring SCK low */
CS=0;/* Bring /CS low */
aa=WRDI_INST;
outbyt(aa);/* Send WRDI instruction */
SCK=0;/* Bring SCK low */
CS=1;/* Bring /CS high */
}

/*;********************************************************
*
;* Name: WRSR_CMD
;* Description: Write Status Register
;* Function: This routine sends the command to write the WD0, WD1, BP0 and BP0 EEPROM
;* bits in the status register
;* Calls: outbyt, wip_poll
;* Input: None
;* Outputs: None
;* Register Usage: A
;********************************************
*/
/*寫狀態寄存器子程序*/
void wrsr_cmd(void)
{
uchar aa;
SCK=0;/* Bring SCK low */
CS=0;/* Bring /CS low */
aa=WRSR_INST;
outbyt(aa) ;/* Send WRSR instruction */
aa=STATUS_REG;
outbyt(aa);/* Send status register */
SCK=0;/* Bring SCK low */
CS=1;/* Bring /CS high */
wip_poll();/* Poll for completion of write cycle */
}

/*;*************************************************************
*
;* Name: RDSR_CMD
;* Description: Read Status Register
;* Function: This routine sends the command to read the status register
;* Calls: outbyt, inputbyt
;* Input: None
;* Outputs: A = status registerXicor Application Note AN21
;* Register Usage: A
;*******************************************************
*/
/*讀狀態寄存器,讀出的數據放入到aa中*/
uchar rdsr_cmd (void)
{
uchar aa;
SCK=0;
CS=0;
aa=RDSR_INST;
outbyt(aa);
aa=inputbyt();
SCK=0;
CS=1;
return aa;
}